Show simple item record

dc.contributor.authorGil, Antoni
dc.contributor.authorPeiró Bell-lloch, Gerard
dc.contributor.authorOró Prim, Eduard
dc.contributor.authorCabeza, Luisa F.
dc.date.accessioned2018-07-25T07:55:05Z
dc.date.issued2018
dc.identifier.issn1359-4311
dc.identifier.urihttp://hdl.handle.net/10459.1/64630
dc.description.abstractSolar cooling is a promising solution to overcome the high energy demand of buildings. Nevertheless, the time dependent nature of the solar source leads to the need of storage systems in order to better match the energy demand and supply. For this purpose, thermal energy storage was considered during last decades as the optimal solution at commercial scale. Latent thermal energy storage offers higher energy densities together with more constant outlet temperature than sensible heat storage, but the low thermal conductivities of PCMs represents the main drawback which limits its applicability. Several studies based on heat transfer enhancement techniques applied in latent thermal energy storage have already been performed. Specifically, the technique of adding fins in storage tanks, which is the most known and studied. However, there are few experimental studies at pilot plant scale focused on this technique and less on the analysis of the heat transfer enhancement through the parameter effective thermal conductivity. This paper presents an experimental study where this parameter is determined and compared using of two identical latent storage tanks, one with 196 transversal squared fins and another one without fins. In this case, hydroquinone was selected as PCM. A set of six experiments was performed at pilot plant of the University of Lleida (Spain), combining three different HTF flow rates and two temperature gradients between HTF inlet temperature and initial PCM temperature. Experimental results showed that the addition of fins can increase the effective thermal conductivity between 4.11% and 25.83% comparing the experiment with highest and lowest thermal power supplied to the PCM, respectively.
dc.description.sponsorshipThe work was partially funded by the Spanish government (ULLE10-4E-1305 and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2017 SGR 1537). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
dc.format.mimetypeapplication/pdf
dc.language.isoeng
dc.publisherElsevier
dc.relationMINECO/PN2013-2016/ENE2015-64117-C5-1-R
dc.relation.isformatofVersió postprint del document publicat a: https://doi.org/10.1016/j.applthermaleng.2018.07.029
dc.relation.ispartofApplied Thermal Engineering, 2018, vol. 142, p. 736-744
dc.rightscc-by-nc-nd (c) Elsevier, 2018
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/es
dc.subjectEffective thermal conductivity
dc.subjectPhase change material
dc.subjectSolar cooling
dc.subjectStorage tank with fins
dc.subjectThermal energy storage
dc.titleExperimental analysis of the effective thermal conductivity enhancement of PCM using finned tubes in high temperature bulk tanks
dc.typeinfo:eu-repo/semantics/article
dc.date.updated2018-07-25T07:55:05Z
dc.identifier.idgrec027236
dc.type.versioninfo:eu-repo/semantics/acceptedVersion
dc.rights.accessRightsinfo:eu-repo/semantics/embargoedAccess
dc.identifier.doihttps://doi.org/10.1016/j.applthermaleng.2018.07.029
dc.date.embargoEndDate2020-07-18


Files in this item

Thumbnail
Thumbnail
Thumbnail
Thumbnail

This item appears in the following Collection(s)

Show simple item record

cc-by-nc-nd (c) Elsevier, 2018
Except where otherwise noted, this item's license is described as cc-by-nc-nd (c) Elsevier, 2018